- 您现在的位置：买卖IC网 > Sheet目录471 > MAX19993ETX+ (Maxim Integrated)IC MIXER DOWNCONV 36TQFN
Dual, SiGe, High-Linearity, 1200MHz to 1700MHz
Downconversion Mixer with LO Buffer/Switch
Applications Information
Input and Output Matching
The RF and LO inputs are internally matched to 50 I .
No matching components are required. The RF port
input return loss is typically better than 19dB over the
1400MHz to 1700MHz RF frequency range and return
loss at the LO ports are typically better than 15dB over
the entire LO range. RF and LO inputs require only
DC-blocking capacitors for interfacing.
The IF output impedance is 200 I (differential). For
evaluation, an external low-loss 4:1 (impedance ratio)
balun transforms this impedance to a 50 I single-ended
output. See the Typical Application Circuit .
Reduced-Power Mode
Each channel of the device has two pins (LO_ADJ_D/
LO_ADJ_M, IFD_SET/IFM_SET) that allow external
resistors to set the internal bias currents. Nominal values
for these resistors are given in Table 1. Larger value
resistors can be used to reduce power dissipation at the
expense of some performance loss. If Q 1% resistors are
not readily available, substitute with Q 5% resistors.
Significant reductions in power consumption can also
be realized by operating the mixer with an optional 3.3V
supply voltage. Doing so reduces the overall power
consumption by approximately 46%. See the 3.3V Supply
DC Electrical Characteristics table and the relevant 3.3V
curves in the Typical Operating Characteristics section.
IND_EXT_ Inductors
The default application circuit calls for connecting
IND_EXT_ (pins 15 and 31) to ground through a 0 I
resistor (0603) as close as possible to the pin. For
improved RF-to-IF and LO-to-IF isolation, contact the
factory for details.
20
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. Keep RF signal lines as short as
possible to reduce losses, radiation, and inductance.
The load impedance presented to the mixer must be
such that any capacitance from both IF- and IF+ to
ground does not exceed several picofarads. For the best
performance, route the ground pin traces directly to the
exposed pad under the package. The PCB exposed pad
MUST be connected to the ground plane of the PCB. It is
suggested that multiple vias be used to connect this pad
to the lower-level ground planes. This method provides a
good RF/thermal-conduction path for the device. Solder
the exposed pad on the bottom of the device package
to the PCB. The MAX19993 evaluation kit can be used
as a reference for board layout. Gerber files are available
upon request at www.maxim-ic.com .
Power-Supply Bypassing
Proper voltage-supply bypassing is essential for high-
frequency circuit stability. Bypass each V CC pin and
TAPMAIN/TAPDIV with the capacitors shown in the
Typical Application Circuit . See Table 1 for component
values. Place the TAPMAIN/TAPDIV bypass capacitors
to ground within 100 mils of the pin.
Exposed Pad RF/Thermal Considerations
The exposed pad (EP) of the MAX19993’s 36-pin TQFN-
EP package provides a low thermal-resistance path to
the die. It is important that the PCB on which the device
is mounted be designed to conduct heat from the EP. In
addition, provide the EP with a low-inductance path to
electrical ground. The EP MUST be soldered to a ground
plane on the PCB, either directly or through an array of
plated via holes.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX19994AEVKIT#
KIT EVAL FOR MAX19994A MIXER
MAX19995ETX+T
IC DOWNCONVERTER 2CH 36TQFN
MAX19995EVKIT#
EVALUATION KIT FOR MAX19995
MAX19996AEVKIT#
EVALUATION KIT FOR MAX19996A
MAX19996ETP+T
IC MIXER DOWNCONV 20-TQFN-EP
MAX19997AETX+T
IC DOWNCONVERTER 2CH 36TQFN
MAX19998ETP+
IC MIXER DOWNCONVERSION 20TQFN
MAX19999ETX+T
IC DOWNCONVERTER 2CH 36TQFN
相关代理商/技术参数
MAX19993ETX+T
功能描述:上下转换器 High-Gain 1.2GHz to 1.7GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19993EVKIT#
功能描述:射频开发工具 High-Gain 1.2GHz to 1.7GHz Downconv RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MAX19994AETX+
功能描述:上下转换器 High-Gain 1.2GHz to 2GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19994AETX+T
功能描述:上下转换器 High-Gain 1.2GHz to 2GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19994AEVKIT#
功能描述:射频开发工具 RF and RFID RF Evaluation & Development Kits & Boards - KIT EVAL FOR MAX19994A MIXER RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MAX19995AETX+
功能描述:上下转换器 High-Gain 1.2GHz to 2GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19995AETX+T
功能描述:上下转换器 High-Gain 1.7GHz to 2.2GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19995AEVKIT#
功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V